Plastic guttering is assembled from lengths joined with union brackets, corner pieces and running outlets, each sealed with a rubber gasket. Those seals are what fail most often. On a typical half-round uPVC system, a leak at a joint is almost never a crack in the gutter itself. It is the seal, the alignment, or debris holding water where it should not be.
First, find exactly where the water comes from
A drip on the ground can be a metre away from its source, because water tracks along the underside of the gutter before it falls. Before buying anything, watch the gutter during rain or run a hose into it from the high end, and note:
- Is the water coming from the joint itself, or running back along the underside from somewhere else?
- Does it leak only in heavy rain (overflow) or in every shower (a failed seal)?
- Is the gutter holding standing water near the joint after the rain stops?
If the gutter fills and spills over the front, it is an overflow problem, not a leak, and our guide to overflowing gutters will be more useful.
The common causes
1. Debris sitting on the joint
Silt, moss and leaves collect at joints because the bracket creates a small lip. Water pools there, and even a sound seal will weep if water sits against it for days. Clean the run first, then re-test. A surprising number of "leaks" stop at this stage.
2. A perished or displaced seal
Rubber gaskets harden and crack with age and UV exposure, and they can be pushed out of place if someone leans a ladder on the gutter. On most systems you can unclip the gutter from the union bracket, peel out the old seal, clean the groove and fit a replacement from the same manufacturer. Seals are not universal, so take the old one or the brand name with you.
3. Gutter lengths not seated correctly
uPVC expands and contracts with temperature. Union brackets have insertion marks showing how far each length should go in, leaving a gap for movement. If the lengths were pushed in too far, they can buckle in warm weather. Too little and they pull out of the seal in cold weather. Either way, the joint leaks. Re-seating the lengths to the marks often solves it.
4. Loss of fall
Gutters need a slight fall towards the outlet. Manufacturers usually specify somewhere in the region of 1:350 to 1:600, which is only a few millimetres per metre. If a bracket has slipped or the fascia has moved, water collects in a dip, often right at a joint. A string line from end to end shows any sag quickly. The fix is to reposition or add brackets, usually no more than a metre apart on plastic systems.
5. Mixed brands or profiles
Different makes of half-round gutter look identical but differ by a few millimetres. If a previous repair joined two brands, the seal may never have sat properly. Adapters exist for some combinations, but sometimes the sensible answer is to replace a section with matching parts.
6. Rotten fascia behind the bracket
If the bracket screws will not bite, or the fascia board is soft when you press it, the gutter will keep moving no matter how many seals you replace. This is a fascia job first and a gutter job second. Our fascia, soffit and gutter services page covers replacement boards.
What about sealant?
Gutter sealants and repair tapes are sold for exactly this problem, and they have a place on cast iron and older metal gutters, where joints are bolted and sealed by design. On modern uPVC systems, smearing silicone over a failed gasket is a short-term patch. It stops the expansion joint from moving, the sealant pulls away within a season or two, and you are back to the same drip with extra mess to scrape off. Replacing the seal or the union bracket is a better repair.
For cast iron gutters, joints are usually bolted with a bed of sealant or putty, and re-making them properly involves unbolting, cleaning back to bare metal and re-sealing.
Corners and outlets
Corner pieces and running outlets carry more water than a straight union, so they tend to show problems first. Outlets also catch debris at the top of the downpipe. If the leak is at an outlet, check that the downpipe is clear (see how often gutters should be cleaned) and that the outlet is not cracked. Corners on older systems sometimes split where the gutter was forced in; replacing the corner piece is usually a cheap fix.
Doing it yourself, or not
Changing a seal on a single-storey roof is a reasonable DIY job if you have a sound ladder with a stand-off and someone footing it. On two-storey houses, the Health and Safety Authority's guidance on working at height is worth reading before you start, as ladders are meant for short, light tasks only. Also consider that you may need a second person to hold the gutter while you unclip it, which is awkward from one ladder.
Call a roofer or gutter specialist when:
- The fascia is soft, cracked or pulling away.
- Several joints are leaking at once, which usually means the whole system is at the end of its life.
- The gutter is cast iron or on a protected structure.
- You cannot reach the joint safely.
For homeowners in the Midlands, the homepage covers gutter repair and guttering in Athlone, and the roof repairs page explains what else gets checked when someone is up at roof level.
Frequently asked questions
Usually because the rubber seal has perished or moved, debris is holding water against the joint, the lengths are not seated to the expansion marks, or the gutter has lost its fall and water is pooling at the joint.
On uPVC gutters it is only a temporary patch, because it stops the joint expanding and contracting and usually pulls away. Replacing the seal or union bracket lasts much longer. Sealant is normal on bolted cast iron joints.
Only a slight fall towards the outlet. Manufacturers commonly specify somewhere between about 1:350 and 1:600, which is a few millimetres per metre. Check your gutter brand's fitting instructions.
Not usually. One leaking joint can normally be fixed with a new seal or bracket. If many joints leak, the fascia is rotten or the system is very old, replacement starts to make more sense.
Related guides
- Overflowing Gutters and Blocked Downpipes: Causes and Fixes
- How Often Should Gutters Be Cleaned in Ireland?
- Cast Iron Gutters: Repair, Restore or Replace?
- All roofing and guttering guides
This guide is general information about roofs and rainwater systems in Ireland. Grant schemes, regulations and product guidance change, so check the official source or the manufacturer's instructions before starting work.